A member of the estimating team will be with you shortly!

Knob-and-tube wiring is an old type of electrical wiring that was common in San Francisco and other parts of the United States from the late 1800s to the mid-1900s. It is made up of two insulated copper wires that are held in place by porcelain knobs and tubes. The knobs and tubes are attached to wooden studs or joists, and the wires run through holes that have been drilled in the wood. The black wire is the hot wire, and the white wire is the neutral wire. The two wires are separated by the knobs and tubes to prevent them from touching each other.

If you have knob and tube wiring in your house, you should definitely consider replacing it. K&T wiring is not safe, and it can't handle the electrical demands of modern homes. Plus, if you ever want to sell your house, you'll have a hard time finding a buyer if it has K&T wiring.

Knob and tube wiring can be safe if it's been properly maintained. However, knob and tube wiring was not intended to support modern day electrical loads. There is a higher risk of fire as a result. Also the insulation around the wire breaks down over time and carries a higher risk of catching fire

• Getting Permits

• Installing Romex wire from the panel to each circuit per current code.

• Replacing the electric panel and circuit breakers where necessary

• Installing new outlets, switches, and fixtures.

• Installing new GFCI switches in the kitchen and bathrooms

• Passing Inspection

• Patching drywall and painting

• Increased safety: Knob and tube wiring is not considered to be safe by modern electrical standards. Replacing it with new wiring will help to protect your home from electrical fires.

• Increased capacity: Knob and tube wiring is not able to handle the electrical demands of modern homes. Replacing it with new wiring will allow you to use more electrical appliances and devices without overloading the system.

• Increased value: Replacing knob and tube wiring can protect the intrinsic value of your home.

No, we source the permits, replace the knob and tube wiring, pass inspection, then patch and paint the walls.

• Protects against electrical shock: If a live wire comes into contact with a person or appliance, the ground wire will provide a safe path for the electricity to flow. This will help to prevent electrical shock.

• Prevents electrical fires: If there is a short circuit or overload, the ground wire will help to prevent the electricity from arcing and causing a fire.

• Improves the performance of electrical appliances: Grounding wires can help to improve the performance of electrical appliances by reducing noise and interference.

• Meets electrical code requirements: In most countries, grounding wires are required by electrical code. This helps to ensure that electrical systems are safe and compliant with regulations.

• Safety: Romex has a ground wire, which provides a safe path for electricity to flow in the event of a short circuit or overload. Knob and tube wiring does not have a ground wire, which makes it more likely to cause electrical fires or shocks.

• Durability: Romex is made of a plastic sheath that is resistant to moisture and corrosion. Knob and tube wiring is made of cloth insulation, which can deteriorate over time and become a fire hazard.

• Compatibility: Romex is compatible with modern three-prong appliances. Knob and tube wiring is not compatible with three-prong appliances, which can cause them to malfunction or even start a fire.

• Ease of installation: Romex is easier to install than knob and tube wiring. Romex can be run through walls and ceilings without the need for special fixtures.

It depends on the current state of your electrical panel and the amount of electrical load your home currently uses. If your electrical panel is old or outdated, it may not be able to handle the increased load of the new wiring. In this case, you will need to upgrade your panel.

Here are some factors that will determine if you need a new panel:

• The amperage of your current panel: The amperage of your panel is the maximum amount of electricity it can safely handle. If your current panel is only 60 amps, and you are upgrading to 100 amp wiring, you will need to upgrade your panel.

• The number of circuits in your current panel: The number of circuits in your panel determines how many appliances and devices you can have running at the same time. If you are adding a lot of new appliances or devices, you may need to upgrade your panel to add more circuits.

• The age of your current panel: Electrical panels have a lifespan of about 50 years. If your panel is older than 50 years, it is a good idea to have it inspected by an electrician to see if it needs to be upgraded.

If you are unsure whether or not you need a new panel, it is best to have an electrician inspect your electrical system. They will be able to assess the condition of your panel and recommend whether or not it needs to be upgraded. Here are some benefits of upgrading your electrical panel:

• Increased safety: A new panel will be up to date with the latest safety standards, which can help to prevent electrical fires and shocks.

• Increased capacity: A new panel will be able to handle more electrical load, which will give you more flexibility when adding new appliances or devices.

• Improved performance: A new panel will improve the performance of your electrical system by reducing noise and interference.

Here are some reasons why you might need to replace fixtures when replacing knob and tube wiring:

• The fixtures may not be compatible with the new wiring. Knob and tube wiring is not compatible with modern three-prong appliances. If you are replacing the knob and tube wiring with modern wiring, you will need to replace the fixtures with three-prong fixtures.

• The fixtures may be damaged. If the fixtures are old or damaged, they may not be safe to use. In this case, it is best to replace them with new fixtures.

• The fixtures may not be up to code. Electrical codes have changed over the years. If the fixtures are not up to code, they may not be safe to use. In this case, it is best to replace them with new fixtures that are up to code.